Use of a cordless pole noticed

Do you want a tool to tidy up your garden? You don't need to worry anymore. Get one of the cordless pole saws that can be used to cut and remove branches from your garden. You can also use the saw to chop hard and hard-to-reach areas and perform light cutting work.

Therefore, before we begin, it is important to learn step-by-step how to properly use a cordless pole saw so that you better understand how it works. But first let's understand what a cordless pole is.

What is a cordless pole saw?

It's a tool that runs on a set of batteries that makes the device work without necessarily plugging it into a circuit. A machine is a simple tool, flexible and portable. This machine comes with a chain that cuts trees and branches with ease. Also, you can use it for pruning, jerking, filling, lambing, etc.

Step by step on how to use a cordless pole saw

  1. Prepare the area under your trees

Preparing the area under your trees is the first step before making any cuts. Make sure you clear the area under your trees to avoid damage from falling branches. Clearing the environment is a simple step that should take a few minutes. Make sure to remove any debris that could get in your way while cutting. You can also remove objects that you no longer want to damage.

  1. Position the branch and your rod saw the device

When your branch is ready to be cut, you need to reduce the weight. That way, you can get very clean and minimize the ability of the branch to fall to the middle of the section, which can lead to potential damage. Of course, if you take this step seriously, you will no longer be able to work with it. Make sure that no unwanted pressure is left on the branches. You can also tie it back if possible. This makes clean and controlled cutting easier and gives you additional confidence.

  1. Now prepare to cut

In this step, make sure you wear non-slip gloves for protection. When the engine is running, make sure that the device always has a good grip. Grasp the handle with your right hand and grasp the rod shaft with your left. Hold the machine with your hands while placing your hands on the rear handle and rod shaft. Never try to use the left handed grip that puts your body on the chain line. In addition, do not stand directly under the limb you are chopping.

  1. Cutting attitude

Make sure you have kept a maximum distance while cutting so that you are in a safe position. Standing cutting is steps away from the branch you are cutting. So if you maintain a safe position, you cannot be hit directly by a falling branch while you are collapsing. When you have positioned yourself in the correct position, grab your bar and saw near your chest using a suitable angle of the bar. Most of the time, a 60 degree angle is suitable for many users depending on specific situations. Make sure you balance your weight with the floor by leaning to the left of the chain line.

  1. Turn on your cordless pole saw

Using the battery compartment, slide the battery in until it fits completely into place. Turn on the machine by holding the safety switch interlock with your thumb near the handle and depressing it while pressing the button trigger switch with your fingers. You can immediately release your safety interlock switch as soon as your pole saw starts operating. Give your machine enough time to accelerate to high speed before you start cutting.

  1. Circumcision and limbs

Limbing removes branches from a fallen tree. First, cut off limbs one at a time and remove the limbs from the work area to keep your space safe and clean. To avoid tying the chain, you can cut the branches from below. Pruning, on the other hand, cuts off branches from a tree that has not fallen or only from a living tree. To do this you need to make the first cut from the bottom of the arm so you can stick with one torso. Next you can make the second cut from the top of the limb. Press gently to cut the chain without damaging the bar.

  1. Turn off your machine

Once you're done, you can let go of the shutter button. If you do not follow the cutting procedures, the chain and bar can connect and pinch the limb. In this case, you can turn off the engine and remove the battery from the machine immediately.

  1. Remove dirt

After successful cutting, all twigs and branches that may be scattered in the cutting area should be removed. When you have completed these steps, you can be sure that you will move to the next branch.

Using a cordless pole saw - pruning

frequently asked Questions

  • What is the best cordless pole saw?

The best cordless pole saw is usually the Greenworks 8.5 40V pole saw. It's the best overall as it has high ratings.

  • Is a Battery Operated Pole Saw Any Good?

The cordless pole saw offers maximum cutting ability conveniently with a battery-operated saw. The device is light and easy to use as it weighs 12.8 pounds.

  • What should I look for in a pole saw?

When looking to buy the pole saw, you should consider the length of the pole saw. The size of your yard in particular is another critical consideration. Hence, if your garden is large, you will need a tall pole saw.

Conclusion

As you can see from our post above, unless you want to complicate the process, it is straightforward to operate your cordless pole saw. Therefore, when cutting hard-to-reach branches with a pole saw, you need to be careful enough and maintain a safe position as it is dangerous. In case of difficulty, you can call the professional arborist to carry out the job on behalf.

Leave a comment